The stability of LaNi5 in a Cu matrix

The reaction of LaNi₅ with Cu powder during sintering at high temperature was examined in order to obtain better conductivity and ductility. Pressurized and forged copper-LaNi₅ pellets were investigated by optical metallography, DTA, XRD and TEM. The need for heat treatment after pressing and/or forging is vital to obtain good diffusion bonding between the copper particles and to improve the material strength. No interaction between La, Ni and Cu were observed after heating at 1173 K but a very stable La₂O₃ phase was created around the LaNi₅ particle. Rolling up to 85% reduction showed good ductility.     

Mixing and solid-liquid mass-transfer rates in a creusot-loire uddeholm vessel: A water model case study

The process of mixing and solid-liquid mass transfer in a one-fifth scale water model of a 100-ton Creusot-Loire Uddeholm (CLU) converter was investigated. The modified Froude number was used to relate gas flow rates between the model and its protoype. The influences of gas flow rate between 0.010 and 0.018 m³/s and bath height from 0.50 to 0.70 m on mixing time were examined. The results indicated that mixing time decreased with increasing gas flow rate and increased with increasing bath height. The mixing time results were evaluated in terms of specific energy input and the following correlation was proposed for estimating mixing times in the model CLU converter: T _mix=1.08Q ^−1.05 W ^0.35, where Q (m³/s) is the gas flow rate and W (tons) is the model bath weight. Solid-liquid mass-transfer rates from benzoic acid specimens immersed in the gas-agitated liquid phase were assessed by a weight loss measurement technique. The calculated mass-transfer coefficients were highest at the bath surface reaching a value of 6.40 × 10⁻⁵ m/s in the sprout region. Mass-transfer coefficients and turbulence parameters decreased with depth, reaching minimum values at the bottom of the vessel.     

The equilibrium partitioning of titanium between Ti3+ and Ti4+ valency states in CaO-SiO2-TiO x slags

The redox behavior of titanium in CaO-SiO₂-TiO _x melts was investigated using a slag-gas equilibrium technique. Titanium partitioning between Ti³⁺ and Ti⁴⁺ valency states and the ratio of activity coefficients of TiO_1.5 and TiO₂ were determined as functions of oxygen partial pressure, temperature, and slag composition. The equilibrium experiments were carried out at temperatures between 1783 and 1903 K under CO-CO₂-Ar gas atmosphere with oxygen partial pressure ranging from 10⁻¹² to 10⁻⁷ atm (1.01×10⁻¹⁰ kPa to 1.01×10⁻⁵ kPa). The slags had CaO/SiO₂ ratios between 0.55 and 1.35 and total titanium oxide concentrations from 7 to 50 mass pct. Experimental results showed that the Ti³⁺/Ti⁴⁺ ratio in CaO-SiO₂-TiO _x slags, containing up to 50 mass pct TiO _x , increased with decreasing oxygen partial pressure and decreased with increasing CaO/SiO₂ ratio and decreasing temperature. Measured variation of the redox ratio Ti³⁺/Ti⁴⁺ with oxygen partial pressure closely followed the ideal behavior. Increasing the CaO/SiO₂ ratio increased the ratio of activity coefficients of TiO_1.5 and TiO₂. The effect of total titania content on this ratio was more complex and in accord with Raman spectroscopy data.     

Synthesis and electrochemical properties of layered Li[Ni0.333Co0.333Mn0.293Al0.04]O2−zFz cathode materials prepared by the sol–gel method

The cathode-active materials, layered Li[Ni_0.333Co_0.333Mn_0.293Al_0.04]O_2−zF_z (0 ≤ z ≤ 0.1), were synthesized from a sol–gel precursor at 900 °C in air. The influence of Al–F co-substitution on the structural and electrochemical properties of the as-prepared samples was characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and electrochemical experiments. The results showed that Li[Ni_0.333Co_0.333Mn_0.293Al_0.04]O_2−zF_z has a typical hexagonal structure with a single phase, the particle sizes of the samples tended to increase with increasing fluorine content. It has been found that Li[Ni_0.333Co_0.333Mn_0.293Al_0.04]O_1.95F_0.05 showed an improved cathodic behavior and discharge capacity retention compared to the undoped samples in the voltage range of 3.0–4.3 V. The electrodes prepared from Li[Ni_0.333Co_0.333Mn_0.293Al_0.04]O_1.95F_0.05 delivered an initial discharge capacity of 158 mAh⁻¹ g and an initial coulombic efficiency is 91.3%, and the capacity retention at the 20th cycle was 94.9%. Though the F-doped samples had lower initial capacities, they showed better cycle performances compared with F-free samples. Therefore, this is a promising material for a lithium-ion battery.     

Microstructural changes accompanying repair welding in 5xxx aluminium alloys and their effect on the mechanical properties

At the shipyards, the aluminium alloy 5083 is welded with a multi-pass sequence using the metal inert gas technique. If, while checking the weld integrity either after welding or during service, defects are detected in the vicinity of the weldment, repairs are usually employed to extend the service life.

The repair method involves removal of the upper passes, depending on the thickness and re-welding under the same conditions.

Purpose of this paper is to examine the microstructural changes accompanying repair welding, define their effect on properties of primary importance and set, if possible, an upper limit as far as the number of repairs is concerned.